BGA Mods Rework and reballing support forum

Worldwide Scotle, Honton and Achi Reseller
Site Announcements

Welcome to BGA Mods Rework Support Forum

Please include pictures to help speed up a solution


Our Worldwide Site

BGA Mods Store

It is currently Fri Sep 19, 2014 8:46 am

All times are UTC [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: ps3 reflow
PostPosted: Sat Sep 01, 2012 11:33 am 
Offline
New Member
New Member
Progress to next rank:
80%

Joined: Tue Aug 28, 2012 10:19 am
Posts: 9
Has thanked: 0 time
Been thanked: 0 time
Set up: achi ir-6000
hello,
I am using achi ir6000 using ps3 support jig
this is my profile for ps3 mobo
TH set at 3cm
bottom heater set to 320
1--step/0/540 Temp of tc showing 145c
2--1/175/47
3--1/190/64
4--1/200/36
5--1/210/70
6--1/225/60
7--end
everything yesterday whilst building profile was spot one.
today near end of run bottom n top heater started glowing.
do you alter height of TH as you go though profile or leave it set.


Top
 Profile  
 
 Post subject: Re: ps3 reflow
PostPosted: Sat Sep 01, 2012 11:42 am 
Offline
VIP Member
VIP Member

Joined: Sun Jun 17, 2012 6:25 pm
Posts: 676
Location: NW England (Wigan)
Has thanked: 0 time
Been thanked: 9 times
Set up: ACHI IR PRO SC - Ayoue 968
The only time you would move the TH during re-flow is to regulate the temperature....i.e. If the temp rises above 224-226 DegC then raise TH a little (1-1.5cm).... :ugeek:

_________________
Success has many Fathers.......

Image Image

Failure is an Orphan.......


Top
 Profile  
 
 Post subject: Re: ps3 reflow
PostPosted: Sat Sep 01, 2012 7:44 pm 
Offline
VIP Member
VIP Member

Joined: Wed Jun 20, 2012 9:44 pm
Posts: 2986
Location: kingslynn,norfolk
National Flag: Great Britain
Has thanked: 535 times
Been thanked: 403 times
Set up: highly modded achi ir6000,2400w switched bottom,omega tc port,internal vac pump
i use this machine and dont have to move the top heater until profile is finnished now i have it set up nicely, couple points to consider, are u using it with the jig sat just on the machine??, are u placing the tc in the exact same point each time? and it does have to be prettyt much exactly imo, moving a bit does result in slight temp differnces, are the enviromental conditionms the same, i.e u dont have a door open one time then closed the next??

_________________
http://www.bgamods.com/forum/search.php, try it :)


Top
 Profile  
 
 Post subject: Re: ps3 reflow
PostPosted: Sat Sep 01, 2012 10:38 pm 
Offline
Moderator
Moderator

Joined: Sun Jun 17, 2012 8:58 pm
Posts: 1541
Location: cornwall

br3tt1
National Flag: Great Britain
Has thanked: 215 times
Been thanked: 166 times
Set up: scotle hr 6000 and Ayoue 968
get rid of the tc and change to a omega tc from karl mate CLICK HERE


Top
 Profile  
 
 Post subject: Re: ps3 reflow
PostPosted: Sun Sep 02, 2012 9:49 am 
Offline
New Member
New Member
Progress to next rank:
80%

Joined: Tue Aug 28, 2012 10:19 am
Posts: 9
Has thanked: 0 time
Been thanked: 0 time
Set up: achi ir-6000
all ready had one thats why redid my profile for ps3.
going to get another one for my ex thermometer
tested the Resistance of top heater was getting 112, i know 122 is norm doe's anybody know whats
the acceptable range for heater?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: